canon mg3500 Setup and Drivers Software Download

Canon MG3550 Setup - PIXMA MG3500 Wireless Connection Setup - How to setup the wireless connection to the printer PIXMA MG3500 as well as how to reset the printer to factory setting.

Most of the access point (sometimes said to be a router or a hub) have automatic dialing keys have loabel "WPS" stands for the so-called Wi-Fi Protected Setup.
It's very likely allowed the tool as you PIXMA MG3500 to connect to your network without the need to enter a password, and quite possibly how fast and easy to connect your device.

canon mg3550 Setup and Drivers Software Download
canon mg3550 Setup

This method is by far the easiest step to connect you PIXMA MG3500, so if your access point has a WPS button please specify 'Connection How to WPS' tab below to guide on connecting using this method.

If your router does not support WPS we had already prepared an alternative guide to get you PIXMA MG3550 connected so please specify the tab 'Standard Connection Method' below

WPS (Wi-Fi Protected Setup) Connection Method


Before we begin, there are many prerequisites that need to be met to use WPS push button method:

The access point must have a physical WPS push buttons.
Please check with your device manual for details.
When WPS button choke nobody, wear guides on the Connection tab Standard Method.

Your network must use WPA (Wi-Fi Protected Access) or WPA2 security protocol. Generally WPS access points using this protocol.

Step 1

Make sure that the printer is turned on.

Press and hold the Wi-Fi button MASTER Picture_PIXMA Wireless Connection Wifi button at the top of the printer until the alarm light flashes once.

Step 2

Make sure that the light next to the button starts flashing blue and then go to your access point and press the WPS button span of 2 minutes.

The (blue) Wi-Fi lamp on the printer always fl ashing when searching, as well as the capability as well as Wi-Fi lamp will blink when connecting to the access point.

When the printer is successfully making a connection to your wireless network, capabilities and Wi-Fi lamp will stop flashing and remain lit.

confirmation tissue preparation

To confirm if your printer is successfully connected to your wireless network, you can print your printer network preparation if you want:

1. Make sure that your printer is turned on.

2. Put a sheet of A4 or letter size paper general.

3. Press and hold the Resume / Cancel MASTER Picture_PIXMA Wireless Connection Setup Page button stop button until the alarm lamp MASTER Picture_PIXMA Wireless Connection tab 1_2 flashes 15 times, and then release it.
Network information page will be created.

When referring to the results to make, check if the "Connection" show "Active" and if SSID - Service Set Identifier (wireless network name) show the correct name of your wireless network.

This concludes the WPS setup procedure.


Hoping this time to continue with the install software to make some of you PIXMA MG3500.

If you do not have the installation CD included with your product, you can download the manual and the software to select your product from the page PIXMA range.

If the wireless setup WPS is still not successful after follow these tips, please contact us for further assistance.

PIXMA MG3550 Standard Connection Method


Step 1

1. For Windows users, the CD input is included with your printer and drive setup.

If you do not have the installation CD included with your product or you are a Mac user, you can download the manual and the software to select your product from the page PIXMA MG3550 range.

2. At the beginning of the monitor appears, click Next.
2 Clink Here For More Information

How To Reset the PIXMA MG3550 preparation of network you are back at the factory default setting


If you need to adjust again preparing your network back to the factory defaults, for example if you change your access point, you can do it by following these guidelines.

Wish noted that negates all initialization tissue preparation on the machine, to print or scan from a computer via the network is going to be impossible until it is re-configured printer with the preparation of the new network.

Follow the procedure below to initialize the preparation of the network:


1. Press and hold the Resume / Cancel PIXMA Wireless Connection Setup button until the page stops flashing alarm lights Connection PIXMA Wireless tab 1 to 17 times

2. Resume / Cancel PIXMA Wireless Connection Setup button to stop page.

Preparation of the network is laid out again back on the preparation of the factory default.

When this system is still not successful after follow these tips, please contact us for further assistance.